Ottoseal S18 Silicone Swimming

Ottoseal S18 Silicone Swimming

Product Info:

Ottoseal S18 pool Silicone is extremely resistant to a Dauernassbelastung. It is equipped strong fungicidal against mold infestation. Resistant to chlorine and very weather and resistance to aging.

• Neutral curing RTV-1 silicone sealant
• Extremely resistant to Dauernassbelastung 
• Stark with fungicide 
• High tear resistance 
• Resistant to chlorine in the pool for disinfection necessary concentration 
• Non-corrosive 
• UV resistant 
• Large adhesion to various materials z.T. in conjunction with coupling agents 
• Very good weathering and aging resistance

 Note:

• Ottoseal S 18 is not suitable for drinking water containers. For this we recommend Ottoseal S27
• Ottoseal S 18 is not suitable for aquariums. For this we recommend Ottoseal S28 
• Ottoseal S 18 is not suitable for marble / natural stone swimming pools.For this we recommend Ottoseal S70

 Applications:

• Sealing and grouting in the underwater area of pools and baths, etc.

 Processing:

During the hardening gradually small amounts of a neutral cleavage product will be free. In the final state OTTOSEAL S18 is completely odorless and indifferent. OTTOSEAL S18 is equipped highly resistant to salt water and fungicide and chlorine in the usual concentrations in the pool. To minimize the risk of mold growth on the swimming pool silicone OTTOSEAL S18, the following guidelines be followed by the swimming pool operation: The disinfection of swimming pool water with chlorine is essential. It can also
alternative methods are used. An adequate chlorine disinfection must however be compulsory in place to effectively prevent a mold infestation. The alternative methods, such as for example, have ultraviolet radiation or ozonation no disinfectant residual effect. This is essential to prevent mold growth. We recommend cleaning the cured sealant before filling the pool with clean water to the Glättmittelrückstände
to remove surface. Glättmittelrückstände may encourage the dispersal of microorganisms and cause a mold infestation.
Water, with the following characteristics:
Pool 0,3 - 0,6 mg / l free chlorine
Warmsprudelbecken 0.7 to 1.0 mg / L free chlorine
Currently, there is prior art that a concentration of free chlorine is allowed to 1.2 mg / liter.
The pH of the bath water is optimal at a value of 7.0 set.
Deviations above and below 6.5 to 7.6 are allowed for freshwater it. should be noted however that: power is too strong a lovely smell of chlorine apparent, the cause may possibly wrong in a
pH of pool water are. This check and adjust to the optimum value.
Indispensable is a regular circulation of water. This must always be in operation and must not be temporarily interrupted. Interruptions may occur partially through very different levels of chlorine, the minimum concentration of 0.3 mg / liter may be some places below. Such underspends lead to the buds of the ubiquitous spores and mold growth. When properly
Water circulation is to run the pool water constantly over the overflow edge of the pool. In the case of the use of cleaning agents, you must ensure that not only acidic cleaning agents are used, but is neutralized by a subsequent cleaning with alkaline detergents. The risk of mold infestation is increased by the use of such funds. In the rehabilitation of contaminated silicone sealant joints must be completely removed and the surface with anti-mildew spray to be disinfected. Otherwise, grow in
Sealant invading fungal spores rather quickly by the renewed sealant to the surface. The curing time is extended with increasing thickness of the silicone. One-component silicone adhesive bonds are not suitable for flat, unless the specific design requirements for this are given.

Storage:

12 months from date of manufacture in unopened packaging in a cool (+5 ° C and +25 º C) and dry storage. Opened container tightly closed and short-term use.

Form:

310 ml cartridge (20 Katuschen per carton)

Color:

white, gray, silky gray

>> Technical Data <<

>> Safety data sheet <<