Ottopur Turbo

model
OPTU-21
manufacturer
OTTO Chemie
OTTO Chemie

Ottopur Turbo the 2K frame foam for the assembly and insulation of door frames and window frames made of wood, steel or plastic in masonry.


5,95EUR / cartridge
baseprice: 2,83EUR / 100 ml
incl. 19% VAT plus shipping costs (to DE)
Delivery beginn within 2 - 10 daysDelivery beginn within 2 - 10 days **


Ottopur Turbo

Product info Ottopur Turbo 2K frame foam:

Ottopur Turbo the 2K frame foam for the assembly and insulation of door frames and window frames made of wood, steel or plastic in masonry.

  • 2-component mounting foam based on polyurethane
  • LPG free
  • Extremely fast curing
  • Resilient within a few minutes
  • Cuttable at 20 ° C after approx. 5 minutes
  • Lather yield approx. 5.5 liters per 250 g / 210 ml double cartridge
  • Corresponds to building material class B2


Standards and tests:

  • General building inspectorate test certificate - normal inflammable building material (B2) according to DIN 4102-1
  • French VOC emission class A +


Application areas:

  • Assembly and insulation of door frames and window frames made of wood, steel or plastic in masonry
  • Suitable for mounting wooden steps


Special instructions:

With the manual gun 2K H248 we offer a special processing device for this foam Fresh product residues can be removed with acetone or OTTOPUR Cleaner.

Processing:

During assembly, the instructions of the frame manufacturer and the requirements of the state of the art must be taken into account.
1. Wedge the door frame and brace it. The surfaces must be clean, dry, free of dust and grease. Prime highly absorbent and porous (e.g., gypsum and aerated concrete walls) substrates with OTTO Primer 1105.
2. Apply cardboard strips enclosed in the wall gap in the area of the foam dots so that the mixed liquid components do not flow down until they foam (after a few seconds).
3. Floor coverings and adjacent components, if necessary by covering or masking against polluters.
4. Cut off the tip of the cartridge with a knife and attach the mixing nozzle.
5. Using the special manual gun 2K H248, evenly extrude the components, avoid jarring so that the components in the mixing tube are homogeneously mixed.
6. The properly mixed foam should have a light yellow color.
7. Apply the foam through the mixing nozzle in the wall gap, then place the cartridge with the pistol on cardboard or paper as long as foam remains from the static mixer.
8. Immediately remove fresh foam stains with Ottopur Cleaner. Hardened foam can only be removed mechanically.
9. It is recommended to cut foam residues after reaching the assembly strength (despreadable) after approx. 15 - 18 minutes (at + 20 ° C).
10. Lower temperatures extend the cure rate.
11. If the foaming is interrupted, the mixing tube must be removed and later replaced with a new mixing tube.
12. Wooden frames for door leaf weights up to 40 kg must be attached to at least 6 points, each 20 cm in length. Steel frames and all frames with a door leaf weight of more than 40 kg must be completely foamed. The joint gap should not exceed 20 mm. Due to the large number of possible influences during processing and application, the processor must always carry out a sample processing and application.

Storage:

9 months from date of production in unopened packaging in a cool (+ 5ºC and + 25ºC) and dry storage. The foam cans must be stored upright to exclude the sticking of the spray valve. Close open containers well and consume at short notice.

Packaging:

2 x 125 g / 2 x 105 ml double cartridge (16 double cartridges per box)

Colour:

light yellow

Be the first to review this product.

Customers who bought this product also purchased

We Also Recommend