The bathroom is a wet room and must be sealed properly, so that no mold can form. Therefore, you should always provide this room with the waterproofing membrane and also work with good tile adhesives.
Contents:
1.Coupling categories and the appropriate sealing
2. Renovate the waterproofing of the bathroom
3. Models for wall connections and feedthroughs
4.Conclusion
Stress categories and the appropriate seal
There are different stress categories for the correct sealing.
The waterproofing membrane / decoupling mat is used for the stress classes A and C, if it goes to abP. According to the ZDB, the sealing membrane also corresponds to class A0 and B0.
The liquid foil also fulfills certain classes, namely A according to abP and ZDB class A0.
Now there are still sealing slurries, which is used in heavily wet areas, such as in the swimming pool. According to the building rules list, it fulfills classes A and B. According to ZDB, classes A0 and B0.
Renovation of the waterproofing of the bathroom
Of course, you work differently with all materials.
The waterproofing membrane can be pre-painted in advance, but can also work on the bare walls. Cut the waterproofing membrane to the desired size and then apply the tile adhesive to the substrate with a notched trowel and do it completely, paying attention to the open time of the adhesive. Now we pressed the waterproofing membrane completely into the adhesive, before which you can use the smooth side of the toothed spatula or a smoothing spatula. The web should overlap in the joint area in any case 5 cm and with the tile adhesive, also called sanitary silicone, are glued. At edges, pipe ducts and other the overlaps must be glued tight. Once everything has been glued, the coating can begin, you do not need to wait. The tile adhesive for laying tiles can be applied directly to the waterproofing membrane.
In the case of the liquid film, you first apply the primer, then you can turn to the liquid film. This is applied with a smoothing spatula, of course, evenly. You can also use a lambskin scooter, but then the second layer of liquid film must be applied across the first layer so that defects can be avoided. There must always be a second order. This is followed by the tile adhesive, the joint mortar and the sealant.
Even with the sealing slurry, first the pre-coat follows, then the first layer of sealing slurry, then the second layer, followed by tile adhesive, grout and sealant. The sealing slurry is applied with a toothed spatula and must be done twice, because a dry layer thickness of 22 mm must be worked out. Therefore, when working with a lambskin scooter you also need three layers, otherwise the 2 mm can not be achieved.
Version for wall connections and feedthroughs
It is now known that one works with sealing slurry, decoupling mat or liquid foil. But you always have to think in your own bathroom to the particular installation implementation. There is the wall connection wet room, the connection Bodenablaub, the passage in the door area and more. You also need the right products for that. So you can use the sealing tape, when it comes to the connection floor drain with adhesive flange and fabric insert. It can be used to seal the pipe penetrations and pipe runs, as well as the Eckausbildungen for bridging cracks and joints. Even with the object tape you can seal the Eckausbildung and so bridge. Likewise seal the pipe penetrations and pipe runs.
You should also know the bottom gasket, which provides a permanent seal in the floor area at pipe penetrations. It is just right under tiles, ceramic coverings and sheets. You can also opt for external and internal corners, these are elastic corners for a permanent waterproof seal. The wall sealing sleeve could also be important, as it ensures the sealing on walls and also on pipe penetrations. And also the stretch zone cuff is a cuff for the seal, but a very special, which meets the ZDP and abP moisture levels.
You have to think of everything in the bathroom, on the wall connection wet room, on the floor drain, on the connection floor drain with adhesive flange and fabric insert and passage in the door area. If you do, you will seal your own bathroom perfectly and protect it from mold.
Conclusion
In conclusion, it is clear that you have to take care of the sealing of the wet room, especially where the bathtub and shower are. But also the toilet and the sink can be very important. Therefore, it is never wrong, all around with the sealing membrane / decoupling mat, with the liquid foil