Under the term “gluing drywall boards (Rigips)”, one understands the direct fixing of gypsum plasterboards or drywall panels (often known under the brand name “Rigips”) onto a load-bearing substrate using special adhesives and installation methods – instead of a substructure or pure screwing. This process differs from traditional drywall construction with profiles, as the boards are glued directly to the wall or ceiling. One major advantage: less loss of space, reduced effort for substructures, and often faster usability.
Advantages & Properties
- Time and cost-efficient: Gluing drywall boards saves installation time compared to a full frame or profile construction.
- Reduced material usage: No profiles, no substructure, fewer screws or plugs required – ideal for renovation or old building refurbishment.
- Less space loss: A glued board sits closer to the wall than a stud wall with metal profiles – relevant in small rooms.
- Flexible design options: After gluing, the boards can be filled, sanded, painted, or wallpapered – similar to traditional installation.
Typical Application Areas
Interior – Wall Areas
In living spaces or offices, gluing drywall boards is excellent for quickly creating a smooth wall surface – for example, after removing old wallpaper or repairing plaster damage. It is also frequently used for covering electrical or installation areas.
Bathroom and Kitchen (Moist Rooms)
In moist rooms, gluing is possible – but only with suitable moisture-resistant boards (e.g., green impregnated plasterboards) and adhesives designed for higher humidity. Too much moisture or unsuitable adhesives can easily cause damage.
Window Niches, Old Walls & Renovation
In old buildings with uneven or crumbling walls, the gluing method saves time: instead of repairing plaster or installing a full substructure, drywall boards can be applied directly. However, in cases of heavy moisture exposure or very uneven walls, risks are higher.
Exterior Walls / Outdoor Cladding
For exterior walls, gluing plasterboards is not or only very limitedly suitable, as plasterboards are generally not designed for direct outdoor exposure (moisture, temperature changes). A substructure or alternative building material is usually preferable.
Step-by-Step Guide / Application Tips
Check & Prepare Substrate
- Substrate must be clean, dry, stable, and even. Loose plaster, cracks, or highly absorbent surfaces must be treated or removed.
- For highly absorbent walls, priming is recommended before gluing.
- Moist wall areas must be dried – gluing on damp walls risks mold or detachment.
Board Measurement & Cutting
- Carefully measure wall height and width.
- Cut plasterboards with a utility knife and snap cleanly over an edge.
- Ensure clean edges for easier filling later.
Mixing / Preparing Adhesive
- Use special adhesive for plasterboards (e.g., bonding compound or mounting adhesive) – not too liquid, otherwise adhesion fails.
- Pour water first, then add adhesive to avoid clumping.
Applying Adhesive
- Apply adhesive in dabs on the back of the board – usually spaced 30–40 cm apart.
- Keep at least 5 cm distance from the edge to prevent overflow.
Fixing the Board
- Start at the bottom of the wall. Insert spacers (e.g., small wooden wedges) between floor and board to leave a gap (sound insulation, moisture protection).
- Press board evenly, check alignment with a spirit level.
- Stagger board rows, avoid cross joints.
Drying Time & Finishing
- Allow adhesive to cure according to manufacturer instructions before filling or wallpapering.
- Fill joints with filler, sand if necessary, then prime, paint, or wallpaper.
- Seal connection joints (e.g., wall-ceiling or floor-board) with elastic sealant (available at dichtstoffhandel.de) to compensate for movement and prevent cracks.
Common Mistakes & How to Avoid Them
- Damp or unstable substrate: Leads to adhesion loss, mold, or detachment. Solution: check, dry, or use substructure.
- Too little or uneven adhesive: Causes hollow spaces, poor sound insulation. Solution: apply dabs according to instructions.
- Cross joints or unstaggered rows: Can cause tension and cracks. Solution: stagger rows, fill joints properly.
- No expansion joint at wall-ceiling/floor: Risk of detachment or edge cracks. Solution: use sealants or silicone.
- Adhesive processed too late: Some adhesives set quickly; mixing too much at once risks premature binding. Solution: mix only as much as needed.
FAQ – Frequently Asked Questions
How does gluing drywall boards compare to screwing?
Gluing fixes the board directly to the substrate – without substructure or screws – saving time and reducing space loss. Screwing usually requires a drywall profile or wood/metal substructure.
Which adhesive is suitable for plasterboards?
Special gypsum or mounting adhesives (“bonding compound”) as well as high-quality construction adhesives with sufficient adhesion. Ensure suitability for substrate and moist rooms if required.
Can plasterboards be glued to any wall?
No. Substrate must be clean, dry, stable, and even. Strong unevenness, moisture, or crumbling plaster make gluing unsuitable – substructures are better there.
Is gluing plasterboards in bathrooms possible?
Yes, if special moisture-resistant plasterboards (e.g., green impregnated) and suitable adhesive are used. Walls must be dry and system properly planned.
What distance should be left to floor and ceiling?
Leave approx. 2–3 mm gap at the floor (using spacers) and also a small joint at ceiling and wall edges, sealed with elastic sealant – for sound insulation and movement compensation.
Can installations be placed behind glued boards later?
In principle, yes – but installations must be planned before gluing. For extensive installations, substructures are often more flexible.
Note: Technical data and processing instructions depend on the respective manufacturer’s product.