Sikadur 42 HE

model
SD42HE
manufacturer
Sika Chemie
Sika Chemie

Sikadur 42+ HE Cold Climate is a high-performance, self-leveling 3-component grout based on epoxy resin


384,99EUR / bucket
baseprice: 32,08EUR / pro kg
incl. 19% VAT plus shipping costs (to DE)
Scaled Prices
from 24 bucket365,74EUR - you save 19,25EUR, baseprice: 30,48EUR / pro kg
from 48 bucket354,19EUR - you save 30,80EUR, baseprice: 29,52EUR / pro kg
from 96 bucket346,49EUR - you save 38,50EUR, baseprice: 28,87EUR / pro kg
Delivery beginn within 2 - 10 daysDelivery beginn within 2 - 10 days **


Sikadur 42 HE

Product information Sikadur 42 HE:

Sikadur®-42+ HE Cold Climate is a 3-component, high-performance, moisture-tolerant epoxy resin grout that develops high early strength. It is suitable for casting machines or system parts with high static and dynamic loads. The material can be processed up to a layer thickness of 100 mm.

High early strength and rapid curing
High layer thicknesses up to 100 mm
Good fluidity
Good resistance to vibrations Can be used on surfaces with high moisture content
Good mechanical resistance
Very low shrinkage
Low coefficient of thermal expansion
Good creep resistance High reactivity for applications at low temperatures (+5 °C) and rapid increase in strength
Impermeable to most liquids and water vapor
Units ready to mix


Areas of application Sikadur 42 HE:

Sikadur®-42+ HE Cold Climate is only intended for use by commercial processors. High-strength grouting and fastening of: Anchor rods, anchors, tie rods, fasteners, guardrail posts, fence and railing posts Precision grouting of: Machine bases, base plates for light and heavy machinery, including heavy impact and vibration machines, piston engines, compressors, pumps and presses, bridge bearings Repair of : Chipped concrete structures, industrial floor slabs, filling holes and cavities, runways, stands, parking decks


Substrates:

Concrete:
The concrete substrate must be load-bearing and have sufficient compressive strength (> 25 N/mm²) and a minimum adhesive tensile strength of 1.5 N/mm².
The surface must be clean, free of grease and oil, with no loose or poorly adhering parts. Cement skin, paint or other surface treatment agents must be completely removed. Substrates must always have sufficient roughness. Concrete and mortar must be older than 28 days (depending on the required strengths). The surface must be dry.

Steel:
Rust, scale, mortar, concrete, dust and other loose or harmful material that reduces adhesion or contributes to corrosion must be removed. The steel surface must be blasted to a pre-irritation level of Sa 2½ in accordance with DIN EN ISO 12944, Part 4. In cases of doubt, test areas should be created on concrete or steel surfaces.

Concrete, mortar, stone:
The substrate must be free of contamination and the cement slurry must be removed to achieve a rough surface.
Steel:
A purity level of SA 2.5 must be achieved by sandblasting or grinding. Pay attention to the dew point. Surfaces must be clean and solid. For best results the steel should be dry. Dust, cement paste, oil, grease, adhesives, impregnations, waxes, coatings, etc. must be removed mechanically. Anchor holes or sleeves must be free of water. To avoid further corrosion, grouting should be carried out immediately after the substrate has been pre-treated.

Processing instructions:

Mixing ratio:
A: B: C = 6: 1: 28 - 35 parts by weight
Powder / liquid = 4 - 5: 1 parts by weight

Ready packaging:
Add comp. B completely to comp. A. Mix the components A and B in the bucket of the A component with a basket stirrer on an electric hand mixer at low speed (max. 300 - 450 rpm) for 30 to 60 seconds. If possible, do not stir in any air and mix until the material has a uniform color and viscosity. Pour the mixture into a suitable mixing container and slowly add Comp. C, observing the correct mixing ratio. Mix with an electric hand mixer for about 3 minutes until the mortar mixture has an even consistency. Only mix the amount that can be processed within the pot life.
Large containers not pre-dosed:
First mix the individual components thoroughly. Then dose the components in the correct ratio and mix in a suitable mixing container in the same way as in the prepackaged packaging. Opened containers (comp. A and comp. B) must be sealed airtight immediately after use.
Attention: Never mix comp. A and comp. B without adding comp. C and leave to stand (strong heat and smoke development)! Leave SikaDur-42 HE in the mixing vessel until the air bubbles dissolve
have.

Processing:

Before pouring, ensure that the foundation or floor slab is not subject to vibration from nearby machinery. Excessive vibration can cause leakage of the grouting material and affect the curing process. Allow the mixture to vent briefly before processing. Pour the mortar mixture into the prepared filling opening while maintaining sufficient pressure gradient. Pour the mixed mortar continuously into the formwork from one side only to prevent possible air pockets. The air displaced by the mortar must escape properly

en can. Make sure that the casting compound completely fills the space between the substrate and the machine. For this purpose, a flexible steel belt can be moved back and forth under the machine. Pour enough epoxy mortar into the molds so that the mortar extends slightly (3 mm) above the underside of the base plate. After curing, the adhesion strength should be checked with a hammer (impact test).

Device cleaning:

Excess grouting material must be poured into suitable containers for disposal before it hardens.
Wash work equipment immediately with Sika Colma cleaner. Wash hands and skin areas thoroughly with warm, soapy water.
Hardened material can only be removed mechanically.

Storage:

Sikadur 42 HE in the unopened original container when stored in a dry place between +5°C and +30°C. Protect from sunlight.

Delivery form:

Pre-assembled containers (A+B+C): 20.4 kg

Colors:

concrete gray

Be the first to review this product.

Customers who bought this product also purchased

We Also Recommend

Tok Rep
73,19EUR / bucket
baseprice: 36,60EUR / pro kg
incl. 19% VAT plus shipping costs (to DE) and 47,60EUR Mindermengenzuschlag
Produkt innerhalb von 2-3 Arbeitstagen versandfertigProdukt innerhalb von 2-3 Arbeitstagen versandfertig **
(Min quantity: 48 bucket)
TOK® Band SK N2
3.294,59EUR / Pallette
baseprice: 2,75EUR / pro m
incl. 19% VAT plus shipping costs (to DE) and 47,60EUR Mindermengenzuschlag
Produkt innerhalb von 2-3 Arbeitstagen versandfertigProdukt innerhalb von 2-3 Arbeitstagen versandfertig **
Tok Fill
76,99EUR / bucket
baseprice: 3,08EUR / pro kg
incl. 19% VAT plus shipping costs (to DE) and 47,60EUR Mindermengenzuschlag
Produkt innerhalb von 2-3 Arbeitstagen versandfertigProdukt innerhalb von 2-3 Arbeitstagen versandfertig **
(Min quantity: 24 bucket)