Product info:
Ottocoll M595 MS polymer adhesive for flat bonding for tension-equalizing bonding and mounting of different materials. For flat and stress-compensating bonding of a wide variety of materials such as wood, wood-based materials, glass, metals (e.g. aluminium, stainless steel, anodised aluminum, brass, copper), plastics (e.g. rigid PVC, GRP), mineral substrates (e.g. bricks, tiles, ceramics), fire-protected Building boards (plasterboard etc.)
Suitable for use with a spatula - Apply quickly and easily with a toothed spatula
Fills in bumps - rough surfaces possible. Soundproofing effect by filling the cavities
For many substrates without pre-treatment - No pre-treatment even on absorbent substrates such as concrete
Equalizing Tension - Equalizes movement
Low odor - easy to work with
Also adheres to damp surfaces - no lost working time due to drying of the surfaces
Silicone free
Isocyanate free
Solvent-free
Application areas:
Full-surface bonding of wall cladding panels indoors, e.g. in sanitary, kitchen and catering areas and in cold storage cells
For flat and stress-compensating bonding of a wide variety of materials such as wood, wood-based materials, glass, metals (e.g. aluminium, stainless steel, anodised aluminum, brass, copper), plastics (e.g. rigid PVC, GRP), mineral substrates (e.g. bricks, tiles, ceramics), fire-protected building boards
(plasterboard etc.)
Special instructions:
Before using the product, the user must ensure that the materials in the contact area are compatible with it and with each other and are not damaged or changed (e.g. discolored). In the case of materials that are subsequently processed in the area of the product, the user must clarify in advance that their ingredients or vapors cannot lead to any impairment or change (e.g. discoloration) of the product. If necessary, the user must consult the respective manufacturer of the materials. Not suitable for bonding facade panels outdoors. For glass bonding/sealing exposed to UV rays, we recommend using a high-quality silicone adhesive/sealant. In the case of UV-stressed bonding/sealing of transparent plastics such as acrylic glass, we recommend using a high-quality silicone adhesive/sealant. Not suitable for sealing/bonding copper under the influence of UV/temperature. Color shades can be affected by environmental influences (high temperature, chemicals, vapours, UV radiation). This has no influence on the product properties.
pre-treatment:
The requirements for elastic seals and adhesives depend on the respective external influences. Extreme temperature fluctuations, stretching and shearing forces, repeated contact with water, etc. place high demands on an adhesive bond. In such cases, it is advisable to use the primer mentioned (e.g. +/OTTO Primer 1216) in order to achieve the most resilient connection possible. In the case of large-area bonding, sufficient strength of the connection can be achieved on substrates with a recommended primer due to the size of the bonding area, possibly even without a primer (tests/preliminary tests recommended).
Application note:
Fix the materials to be bonded until the adhesive has fully cured. When applying over a large area, the size of the notched trowel should be selected so that there is enough adhesive and both substrate surfaces are sufficiently wetted with adhesive after joining. Insufficient wetting has a negative effect on the bond strength. The time to cure can be shortened by adding moisture and higher temperatures. Moistening is required for the surface bonding of moisture-impermeable materials and to accelerate curing. Due to the large number of possible influences during processing and application, the processor must always carry out a test processing and application. The specific use-by date can be found on the label on the container and must be observed. We recommend storing our products in the unopened original containers in a dry place (< 60% RH) in a temperature range of + 15° C to + 25° C. If the products are stored and/or transported for longer periods (several weeks) at a higher temperature/humidity, a reduction in durability or a change in the material properties cannot be ruled out. Close the opened container again after use. If a skin has formed on the adhesive, it must be completely removed before processing (do not stir in!).
Processing:
Processing temperature: +5ºC to +35ºC.
Application method: Spray with a hand gun, compressed air gun or battery gun.
Cleaning: With turpentine substitute before hardening, then with silicone remover or mechanically removable.
Smooth: With smoothing agent and peel-off spatula before skin formation.
Storage:
Can be stored cool and dry for at least 12 months.
Consumption:
Amount of adhesive [g/m²] : 750g Corresponds to 500 ml with notched spatula B3
Delivery form:
5 kg plastic bucket
Color:
white