Product info:
SikaBond T1 + adhesive is used for structural bonds in construction, such as B. for tiles on balconies, floor slabs, fall protection slabs, for supports of raised floors, for sheet metal cladding and covers in the roofing, plumbing and facade area, for wood and fiber composite components in the interior and exterior finishing area.
- 1-component, ready-to-use
- Solvent-free and very low-emission, EMICODE EC1PLUS R
- Flexible and elastic
- Cures without bubbles
- Excellent adhesion to common building materials
- Good mechanical resistance
- Resistant to aging and weather
- Tolerance compensating
- Shock and vibration absorbing
Application areas:
SikaBond T1 + is an elastic 1-component adhesive based on polyurethane that hardens to an elastomer when exposed to humidity. It is suitable for indoor and outdoor applications. SikaBond T1 + adhesive is used for structural bonds in construction, such as B. for tiles on balconies, floor slabs, fall protection slabs, for supports of raised floors, for sheet metal cladding and covers in the roofing, plumbing and facade area, for wood and fiber composite components in the interior and exterior finishing area.
Chemical resistance:
Resistant to: water, sea water, diluted alkalis, cement mortar and neutral, aqueous cleaning agents
Not resistant to: alcohol, organic acids, concentrated alkalis and acids and chlorinated hydrocarbons
Tests / approvals:
EMICODE EC 1PLUS R, very low emissions
Substrate preparation:
The substrate must be firm, dry, free of oil and grease and free of loose particles or dust. Sinter layers and cement slurry must be removed.
SikaBond T1 + has very good adhesive properties on many clean and solid surfaces. For optimal adhesion and for highly stressed applications or in extreme weather conditions, cleaners and primers must be used. In case of doubt, please carry out preliminary tests. Non-absorbent substrates Glazed tiles, 2-K PU-EP-UP floor coatings or paints, powder-coated metals, aluminum, anodized aluminum, stainless steel and galvanized steel must be coated with a fine abrasive fleece (e.g. siavlies very fine) be sanded with light pressure and cleaned with Sika Haftreiniger-1 with a lint-free cloth. Then let it flash off for at least 15 minutes. Sand all metal surfaces not mentioned above with a fine abrasive fleece (e.g. siavlies very fine) under light pressure and clean with Sika adhesive cleaner-1 with a lint-free cloth. Allow to flash off for at least 15 minutes, then apply Sika Primer 3 N with a brush. Then let it flash off for at least another 30 minutes (max. 8 hours). Hard PVC Apply Sika Primer-215 to the clean surface with a brush. Then let it flash off for at least 30 minutes (max. 8 hours). Porous substrates Concrete, aerated concrete, cement-based plaster, mortar, masonry, weathered wood, etc. Apply Sika Primer 3 N to the clean surfaces with a brush. Then let it flash off for at least 30 minutes (max. 8 hours) Please note: Primers are only to be used as adhesion promoters. They neither replace the cleaning of the adhesive surfaces nor are they able to improve their strength. Primers improve the durability of the seal / bond.
The adhesive surfaces must be cleaned before each primer application! Please note: Primers are only to be used as adhesion promoters. They neither replace the cleaning of the adhesive surfaces nor are they able to improve their strength.
Consumption:
When using the triangular nozzle (10 x 8mm) ~ 44 ml per running meter. This results in approx. 6.5 running meters per 300 ml cartridge.
Processing information:
SikaBond T1 + adhesive can be applied with a hand gun, compressed air gun or battery gun. Apply a triangular bead of the adhesive to the prepared substrate (~ 10 mm high and ~ 8 mm wide). Spread with a notched trowel if necessary. Press the part to be processed firmly onto the adhesive. If necessary, use SikaTack panel mounting tape for fixation. The adhesive thickness must be between 1 and 5 mm, depending on the requirements and the evenness of the surface. Fresh, uncured adhesive must be removed immediately with a clean cloth and, if necessary, with Sika Remover 208 or Sika TopClean T.
Please note:
For better processing conditions, a processing temperature of + 15 ° C is recommended. Sufficient ambient humidity is necessary for perfect curing. (Particular attention should be paid to full-surface bonding.) Do not use on Teflon, PE, PP, polystyrene, bitumen or other surfaces that bleed out with oil or plasticizers, e.g. B. Use EPDM or natural rubber (or carry out preliminary tests or contact your sales advisor). The product must not be used in the uncured state
with isocyanate-reactive substances, especially alcohols, the z. B. are part of alcohol, many thinners, cleaning agents and formwork oil, mixed or brought into contact, otherwise the hardening (crosslinking) of the material is disturbed or prevented.
Storage:
15 months from the date of manufacture when stored in a cool and dry place in undamaged original containers at temperatures between + 10 ° C and + 25 ° C.
Delivery form:
300 ml cartridges (12 cartridges per box)
Colour:
plain white, gray,