Product info:
Sikafloor 701 is a colorless, low-viscosity, 2-component, benzyl alcohol-free epoxy resin binder for priming, leveling and mortar production
High chemical resistance
Bisphenol A and benzyl alcohol free
Almost VOC free
Low viscosity
Simple application
Good penetration behavior
Good adhesive bond
tested as a seal
Application areas:
Sikafloor 701 is intended for use by commercial processors only.
As a primer for concrete substrates, cement mortar and epoxy resin-bound mortar
For normally to highly absorbent surfaces
Primer for Sikafloor floor coatings as a liquid sealant for walls and floors
Processing instructions:
The substrate must be firm and load-bearing and have sufficient compressive strength (min. 25 N/mm²) and an adhesive tensile strength of 1.5 N/mm².
The surface must be clean, dry and free of contamination such as dirt, oil, grease, old coatings and surface treatment agents, etc.
On critical substrates, such as highly absorbent cementitious substrates, the application of a test area is recommended to ensure a pore-free surface after priming.
Layers and dirt that are not sufficiently stable must be removed. Pores and other surface defects must be exposed.
Substrate repairs such as filling pores or reprofiling can be carried out with appropriate Sikafloor®, Sikadur® and Sikagard® products.
Dust, loose and poorly adhering parts must be completely removed, preferably with an industrial vacuum cleaner.
Check moisture content, relative humidity and dew point before application.
Freshly applied Sikafloor®-701 must be protected from steam, condensation and water for at least 24 hours.
Sikafloor®-701 screed is not suitable for constant water contact without sealing.
Create a sample area for screeds to determine the appropriate mixture and the correct grain size of the aggregate.
Apply when temperatures drop to avoid pores. Pores (so-called “pinholes”) can be removed after light sanding, e.g. B. with a scratch filler consisting of Sikafloor®-701 and approx. 3% filler T.
Improper assessment and treatment of cracks can result in reduced lifespan.
If exposed to high temperatures and high point loads at the same time, indentations can occur in screeds.
If an enclosure needs to be heated, we recommend using electric heaters. Combustion heaters lead to the development of water vapor and carbon dioxide, which can affect the coating.
Mix:
Mix up component A briefly. Then add comp. B to comp. A and mix for 2 minutes until a homogeneous mass is obtained. Depending on the system, add filler and mix for another 2 minutes. Repot and mix the mixture again briefly. The introduction of air by mixing for too long must be avoided. Mixing tools are recommended: one- and two-arm basket stirrers (300 - 400 rpm).
Consumption:
Layer product consumption
Primer 1-2 × Sikafloor 701 1-2 × 0.3-0.5 kg/m²
1. Membrane layer (sealing) Sikafloor 701 0.7 kg/m² Glass fiber reinforcement (sealing) Sika Reemat Premium 0.225 kg/m²
2nd membrane layer (sealing) Sikafloor 701 0.3 kg/m² leveling (roughness depth < 1 mm)
1 part by weight of Sikafloor 701 + 0.5 part by weight of quartz sand (0.1–0.3 mm) + 0.015 part by weight of adjusting agent T 1.4 kg/m²/mm
Leveling (roughness depth up to 2 mm)
1 part by weight of Sikafloor 701 + 1 part by weight of quartz sand (0.1–0.3 mm) + 0.015 part by weight of adjusting agent T 1.4 kg/m²/mm bonding bridge 1–2 × Sikafloor®-701 1 -2 × 0.3-0.5 kg/m²
Repair mortar, screed (layer thickness 15–20 mm)
1 part by weight of Sikafloor 701 + 10 parts by weight of quartz sand 2.2 kg/m²/mm
These are theoretical values and do not include any additions for surface porosity, surface roughness, level differences and residual material in the container, etc.
Curing time:
Waiting time before applying solvent-free products on Sikafloor 701:
Underground temperature minimum maximum
+10°C 60 hours - 4 days
+20°C 24 hours - 2 days
+30°C 16 hours - 24 hours
The times stated above are approximate and may vary depending on the processing parameters.
Storage:
Unopened containers will last for at least 2 years if stored in a cool, dry place.
Delivery form:
10 kg Comp. A: 8.50 kg Comp. B: 1.50 kg
25 kg Comp. A: 21.25 kg Comp. B: 3.75 kg
Colors:
This product is a production product and cannot be exchanged!