Soudal Flexifoam Gun Foam – Highly Flexible PU Foam
Soudal Flexifoam is a professional gun foam that is approximately 3x more flexible than conventional PU mounting foams. Even strong structural movements are permanently absorbed, preventing foam tears, reduced thermal and acoustic insulation, and water penetration into joints. Thanks to its excellent dimensional stability, Flexifoam offers minimal shrinkage and controlled expansion.
Key Features
- Approx. 3x more flexible than standard PU foam
- Absorbs high structural movements permanently and reliably
- Prevents foam tears, loss of insulation, and water ingress
- Excellent dimensional stability with minimal shrinkage
- Outstanding adhesion on almost all building substrates (except PE, PP, PTFE, and silicone)
- Higher sound and thermal insulation compared to mineral wool, cork, and fiberglass
- Precise and economical application with dosing gun due to low expansion
- Fast curing
- Resistant to many solvents, paints, and chemicals
- Durable, rot-proof, but not UV-resistant
Applications
- Insulation in refrigerated vehicles, cold rooms, and heating installations
- Fixing and filling in apparatus and metal construction as well as electrical installations
- Mounting and foaming of window and door frames, window sills
- Soundproofing
- Foaming cavities such as wall penetrations, roof extensions, door frames, pipe passages, roller shutter boxes, etc.
Suitable Substrates
Compatible with common building substrates such as concrete, masonry, stone, plaster, wood, metal, polystyrene, PUR rigid foam, polyester, and rigid PVC. Not suitable for PE, PP, PTFE, and silicone. Substrates must be load-bearing, clean, dust-free, and grease-free.
Pre-treatment: Lightly moisten surfaces to improve adhesion, curing, and foam cell structure. Always perform adhesion and compatibility tests.
Processing Instructions
Protect adjacent surfaces before work. Lightly moisten porous substrates. Screw the can firmly onto the gun and shake vigorously (approx. 30 times) to mix contents. Adjust foam bead with the adjustment screw and apply PU foam using the trigger. Fill joints and cavities only about 2/3, as foam expands further. Spray fresh foam lightly with water to improve cell structure, curing, and yield. Cut off excess cured foam with a sharp knife.
Processing Temperature
- +5°C to +35°C (substrate temperature)
- +5°C to +25°C (can temperature)
If necessary, bring can slowly to approx. +15°C in cool or warm water.
Cleaning: Use gun cleaner before curing, afterwards remove mechanically or with PU remover.
Repair: Possible with Flexifoam gun foam.
Standards and Approvals
- Building material class B2 (DIN 4102-1), test certificate P-SAC 02/III-164 (MFPA Leipzig)
- Thermal conductivity (DIN 52612), test certificate 070598.1-Hu (MPA Bau Hannover)
- Joint sound insulation (EN ISO 717-1): RST,w (C;Ctr) = 60 (-1;-4) dB (10 mm joint width), RST,w (C;Ctr) = 60 (-1;-4) dB (20 mm joint width), test report 16733428 (ift Rosenheim)
- Water vapor permeability (DIN EN ISO 12572), test report 50933428 (ift Rosenheim)
- Air permeability (DIN 18542-based), test report 10533428 (ift Rosenheim)
Notes
Cured polyurethane foam must be protected against UV exposure by painting or sealing with sealants (e.g. silicone, polyurethane, acrylic, or MS polymer).
Storage
Shelf life: 18 months from production date in unopened packaging. Store upright at +5°C to +25°C in a cool, dry place. Opened containers must be sealed tightly and used quickly.
Packaging
750 ml aerosol can Flexifoam