Hydrophobization of building materials
Water can cause great damage to buildings. When moisture penetrates house walls such as brick, plaster or concrete, it causes a number of problems. The penetrated water into the building material can frost damage, salt or pollutant deposits and the biological growth of algae, lichens, moss and fungi is promoted. A not to be despised serious disadvantage with rising Enegiekosten is the deterioration of the heat insulation true to the motto: "A wet coat does not warm".
Contents:
1. Term / Explanation
2. mode of action
3. advantages
4. Application
5. Conclusion
1. What does hydrophobing mean
A hydrophobing is an impregnation of a building material so that a water-repellent effect is achieved. The term hydrophobic comes from ancient Greek and means "water-repellent".
2. The mode of action of a hydrophobization
The principle of hydrophobization is to reduce the surface energy of mineral building materials such as brick, concrete or plaster. Water has a relatively high surface tension attracted by high energy surfaces (such as concrete, aerated concrete, fiber cement, brickwork, limestone, natural and artificial stones, mineral plasters and mineral paints). The fact that the surface energy is reduced by means of hydrophobing, the water is no longer attracted but repelled (lotus effect). Modern water repellents are, for example, siloxanes such as the siloxane 290 L. These are so-called zwitterion (a molecule having two or more functional groups), which have a hydrophobic, so water-repellent, and a hydrophilic, so hydrophilic part. Thus, the hydrophilic side of the molecule connects to the mineral building material surface. In addition, the molecules combine with each other to form a silicone. This creates a new, hydrophobized surface. Since silanes are liquids with very small molecules, they are absorbed by the pore system of the building material. As a result, the building material is impregnated or hydrophobicized to a depth of a few millimeters. Although the hydrophobing is invisible per se, such a hydrophobized building material is so water-repellent that, for example, rainwater even in smaller cracks can not penetrate.
3. Advantages of a hydrophobization
A hydrophobized building material has a water-repellent effect, or at least will greatly reduce its water absorption. The hydrophobing agent occupies the inner pore and capillary surfaces of a building material and thereby makes them water repellent. However, the pores and capillaries are not closed, so that the diffusibility (breathability) of the building material, especially in masonry, remains virtually unchanged. This prevents water from entering the building material. No salts or harmful substances, algae and fungi or forest damage can occur. The fact that masonry is not wet, it can not be cooled down by wind.
- Hydrophobic (water repellent) effect
- No forest damage in the masonry
- No salt, algae or fungus deposits
- Energy savings of up to 6%
- Building materials are preserved
- less tendency for pollution
4. Application of hydrophobization
Preparation for the hydrophobization:
The aim is to obtain a good effectiveness of the hydrophobing over a long period of time and without negative side effects. Therefore, the following should be considered before applying the water repellent: The surface should be free of dust, grease, load and largely dry. Weathered surfaces with efflorescence should be pretreated by sandblasting or steam blasting or washing with suitable cleaners. Remove moss, mold and algae completely with mold remover. Splashes on adjacent areas, e.g. Avoid glass, window and door frames made of wood and metal, gutters and elastic expansion joints by covering. This also applies to adjacent facades whose color can be deepened by water repellents. Plastics in the façade or flat roof area must be tested for compatibility prior to waterproofing.
Order of hydrophobization:
There are different methods by which the hydrophobing can be applied to the facade. The best known and simplest method is the spray method. In the simplest case, the surface of the building material is sprayed with a pump spray container until it shines matt-wet. Afterwards, the material penetrates into the pores and reacts. The amount of the applied hydrophobing agent is usually not determined at all and often very inaccurately. Too much active ingredient leads to gloss or white spots on the building material surface, too little material is not permanently effective. The consumption of siloxane is different for the individual building materials:
Concrete 0.25 - 0.5 liters / m2
Plaster 0,5 - 1 liter / m2
Sand-lime brick 0.4 - 0.7 liters / m2
Brick wall 0.4 - 2 liters / m2
Aerated concrete 0.5 - 2 liters / m2
Cement fiber boards 0.1 - 0.3 liters / m2
Natural stone 0.05 - 3 liters / m2
Purification of the hydrophobization:
If, despite covering the surfaces that are not to be impregnated (window panes etc.), impregnating solution has reached areas where it should not go, it is possible to remove a fresh solution by wiping with a cloth and rinsing with detergent. Once the water repellent has dried, this is no longer possible. For this case you need silicone remover. On glass surfaces, this works quite well, but on painted window frames, etc. The silicone remover can cause paint damage.
5. Conclusion
The hydrophobization of masonry offers a lot of advantages it not only protects the building materials but the thermal insulation is improved and saves heating costs.