Ottopur OP920

model
OP920-82
manufacturer
OTTO Chemie
OTTO Chemie

Ottopur OP920 ✔ 2-component PU adapter foam ✔ very fast curing ✔ indoor & outdoor use ✔ excellent thermal insulation ✔ strong sound insulation ✔ universally applicable


9,95EUR / can
baseprice: 2,49EUR / 100 ml
incl. 19% VAT plus shipping costs (to DE)
Scaled Prices
from 12 can9,65EUR - you save 0,30EUR, baseprice: 2,41EUR / 100 ml
from 24 can9,45EUR - you save 0,50EUR, baseprice: 2,36EUR / 100 ml
Delivery beginn within 2 - 10 daysDelivery beginn within 2 - 10 days **


Ottopur OP920

Ottopur OP920 – 2K PU Fast Foam
Non-sticky after approx. 20 minutes, cuttable after 40 minutes, fully loadable after 1.5 hours. Ottopur OP 920 2K PU Foam is perfectly suited for the installation of wooden stair treads.

  • 2-component polyurethane assembly foam
  • Fully loadable after approx. 1.5 hours
  • Non-sticky after approx. 20 minutes
  • Cuttable after approx. 40 minutes
  • Meets building material class B2 (DIN 4102-B2)
  • Ozone-friendly according to the Montreal Protocol
  • CFC-free propellant
  • Complies with the "50-gram rule" (contains only propellant mixtures with a propane-butane content of max. 50 g per 750 ml filling volume)
  • Foam yield approx. 10 liters per 400 ml can

Standards and Testing

Tested according to DIN 4102-B2 – normally flammable.

Applications

  • Installation and insulation of wooden, steel, or plastic door frames and window frames in masonry
  • Ideal for mounting wooden stair treads

Special Notes

The can is under pressure. Protect from sunlight and temperatures above +50 °C. After mixing, the PU foam cures at room temperature within approx. 150 minutes through chemical reaction of the two components. The foam must be processed immediately after activation. Empty the can within 4 minutes (pot life at 20 °C), otherwise curing occurs inside the can (risk of bursting). Higher temperatures shorten the processing time. Do not use cans warmer than +25 °C. If necessary, cool the can in a cold water bath before use.

The PU foam is adapted to normal building moisture and absorbs it during curing without impairing adhesive strength. Do not additionally moisten substrates or foam. Excessively wet substrates may cause shrinkage. The cured foam is semi-rigid, elastic, predominantly closed-cell, rot-resistant, resistant to water, heat, cold, and aging, but not UV-resistant. Building elements must be stable and professionally installed. Maximum joint width for door frame installation: 30 mm. Avoid bonding vibrating components. Do not use with gas-tight materials (e.g., sheet metal) without prior testing. Fresh residues can be removed with acetone or OTTOPUR Cleaner. Avoid skin contact. Cured foam can only be removed mechanically. In case of skin contact, wash immediately with water and soap.

Processing Instructions

  1. Wedge and brace the wooden frame. Max. joint width: 30 mm. Clean dusty substrates and prime with OTTO Primer 1105.
  2. Activate the can by turning the inner base 4 full turns (360°) to the right until it stops.
  3. Shake the can vigorously (20–30 times). A rattling sound confirms activation.
  4. Remove the cap and screw the angled adapter firmly onto the valve – do not damage the valve.
  5. Begin processing immediately after activation and shaking. Foam output can be regulated by pressure or adapter angle.
  6. Press the adapter carefully to control foam quantity.
  7. Check: foam must be consistently pink when exiting. If not, repeat activation and shaking.
  8. Process within 4 minutes after mixing. Unused foam may cause the can to overheat above 50 °C – risk of bursting.
  9. Apply foam on both sides of the door frame at 3 points (hinge and lock height). For steel frames, fill the joint completely. Max. temperature: +23 °C.
  10. Use braces throughout the curing time.

Storage

12 months from production date in unopened packaging at cool (+5 °C to +25 °C), dry storage. Store cans upright to prevent valve sticking. Opened containers must be sealed tightly and used quickly.

Delivery Form

400 ml aerosol spray can (12 cans per carton)

Color

Green

From August 24, 2023, appropriate training must be provided before industrial or commercial use. See the foam can for more information.

FlammeAusrufezeichenGesundheitsgefahr
Gefahr
Extrem entzündbares Aerosol.Behälter steht unter Druck: kann bei Erwärmung bersten.Kann vermutlich Krebs erzeugen.Gesundheitsschädlich bei Einatmen.Kann die Organe schädigen bei längerer oder wiederholter Exposition.

Be the first to review this product.

Customers who bought this product also purchased

We Also Recommend