Sealing the shower before laying tiles is a crucial step to ensure that no moisture penetrates the walls or floor. Proper waterproofing prevents costly damage and guarantees long-lasting tile installation. Follow these essential steps for effective shower sealing:
Preparation
Before starting the waterproofing process, make sure the surface is clean and dry. Remove all loose particles and ensure that no moisture is present. A well-prepared surface is the foundation for durable sealing.
Applying Waterproof Slurry
Waterproof slurry is a key element in shower sealing. It is applied directly to the surface and acts as a barrier against moisture. Spread the slurry evenly with a trowel and smooth it out to create a consistent protective layer.
Using Sealing Tape and Collars
After applying the slurry, place sealing tape along the corners and edges of the shower. Press the tape firmly into the slurry to ensure strong adhesion. Sealing collars should be installed around all pipe penetrations, such as water lines and fixtures, to prevent leaks.
Applying Liquid Membrane
Once the sealing tape and collars are in place, apply a liquid membrane. This creates an additional waterproof layer that covers the slurry, tape, and collars. The liquid membrane enhances protection and ensures complete sealing.
Drying Time
Allow the waterproof slurry and liquid membrane to dry completely before laying tiles. Drying times may vary depending on the product used, so always follow the manufacturer’s instructions.
Laying the Tiles
After the waterproofing has fully dried, you can begin tiling. Use a suitable tile adhesive and press the tiles firmly onto the sealed surface. Proper adhesion ensures a durable and moisture-resistant finish.
Ottoflex floor sealing collar ✔ fleece-laminated on both sides ✔ elastic and tear-resistant ✔ permanently waterproof ✔ suitable for indoor and outdoor…
Ottoflex external corner ✔ elastic seal ✔ permanently waterproof ✔ for external corners under tiles & slabs ✔ very low emissions ✔ tested according to…
Ottoflex sealing tape ✔ elastic and tear-resistant ✔ fleece-laminated special elastomer ✔ indoor & outdoor use ✔ durable & DIN-compliant ✔ reliable …
Displaying 1 to 16 (of 16 products)
Steps for Sealing a Shower with Liquid Membrane
Proper shower waterproofing is essential to prevent water damage. One of the most effective methods is using a liquid membrane. Below are the detailed steps to seal your shower with OTTOFLEX liquid membrane:
Preparation of the Liquid Membrane: Stir the liquid membrane thoroughly before application. Use a short-pile lambskin or foam roller for best results.
Sealing the Corners: Start with wall corners and wall-to-floor junctions. Apply OTTOFLEX sealing tape into the fresh liquid membrane and press it firmly, covering the fabric with the coating.
Applying the Liquid Membrane: Apply evenly on walls and floors. Allow at least 1 hour drying time before the second coat.
Second Coat: Mix OTTOFLEX color paste into the liquid membrane until homogeneous. Apply the tinted membrane. A third coat is optional but not required.
Tile Installation: After 2–3 hours drying time, standard thin-bed tile adhesive can be applied directly onto the membrane.
Wall and Floor Sealing: For floor-only sealing, extend the membrane at least 5 cm up the wall and cover with the skirting. Wall sealing must reach at least 20 cm above the highest water outlet (e.g., showerhead).
Sealing Joints and Pipe Penetrations: Apply OTTOFLEX liquid membrane generously in corners. Seal joints with OTTOFLEX sealing tape and inner corners. Press tape firmly and smooth material. Seal pipe penetrations with OTTOFLEX sealing collars.
Second Application: Respect drying times and apply a second coat for maximum protection.
Sealing with Waterproof Slurry
Preparation of OTTOFLEX Primer: Stir or shake thoroughly before applying with brush or roller.
Mixing OTTOFLEX Waterproof Slurry: Add two-thirds of water to powder, mix at approx. 600 rpm. Add remaining water and mix for 3 minutes. Avoid lumps.
Maturation: Let the slurry rest briefly, then remix. Use within 1 hour.
First Application: Apply evenly with trowel, brush, or spray machine. Check thickness with gauge: Class A = 1.25 mm, Class B (underwater) = 1.00 mm. Add 25% for uneven surfaces.
Installing Tapes, Corners, Collars: Place onto fresh coat, overlap joints by 5 cm, embed with second coat.
Drying Time: Allow approx. 3 hours for first coat.
Second Application: Apply second coat, embedding tapes and collars. Respect required thickness.
Drying Second Coat: Allow approx. 3 hours drying time.
Further Processing: After 24 hours, apply C2 tile adhesive tested in OTTOFLEX system. For Class B, apply a third coat (1 mm wet thickness).
Sealing with Sealing Membrane and Decoupling Mat
Preparation of OTTOFLEX Primer: Stir or shake thoroughly, apply evenly with brush or roller.
Cutting OTTOFLEX Membrane: Cut to size, paying attention to pipe connections and details.
Applying C2 Tile Adhesive: Spread evenly on surface.
Installing Membrane and Mat: Press into adhesive starting from corners. Use smooth side of trowel to press firmly.
Sealing Transitions: Lay membranes edge-to-edge (not overlapping). Seal joints with OTTOFLEX sealing tapes and Ottocoll M500/M595 hybrid adhesives.