82,09EUR / Sack
baseprice: 4,10EUR / pro kg
incl. 19% VAT plus shipping costs (to DE)
Scaled Prices
from 10 Säcke77,99EUR - you save 4,10EUR, baseprice: 3,90EUR / pro kg
Delivery beginn within 2 - 10 daysDelivery beginn within 2 - 10 days **


Ottoflex sealing slurry

One-Component Flexible Composite Waterproofing Slurry

  • Crack-bridging
  • Easy to apply
  • Crack-free curing
  • Waterproof and vapor-permeable when cured
  • Frost- and aging-resistant when cured
  • Suitable for indoor and outdoor applications
  • Tested according to the latest guidelines for issuing a general building inspection certificate (ABP) in combination with ceramic coverings, February 2008

Standards and Testing

  • General building inspection certificate for waterproofing in combination with tiles and slab coverings
  • Meets stress classes A1, A2, and B according to abP
  • Meets moisture stress classes 0, A01, A02, and B0 according to ZDB guidelines

Application Areas

  • Flexible composite waterproofing under ceramic coverings on balconies and terraces with a slope > 1%
  • Flexible composite waterproofing under ceramic coverings in wet rooms, bathrooms, and steam saunas
  • Structural waterproofing on basement exterior walls and retaining walls
  • Sealing of swimming pools and water tanks made of solid construction. Approved up to 4 m water depth according to current test principles
  • Suitable for substrates with sufficient strength such as screed, heated screed, concrete, masonry, aerated concrete, and plaster of mortar groups II and III
  • For highly water-stressed areas according to stress classes A1, A2, and B of the building regulations list
  • Only to be used for waterproofing from the positive side

Substrate Preparation

The substrate must be solid, load-bearing, absorbent, and largely even. Contaminants such as oil, grease, or other separating agents must be removed. Cavities and unevenness exceeding DIN 18202 tolerances must be leveled with suitable concrete filler. Pre-wet the substrate thoroughly before applying the slurry. The surface should be matt damp. Residual moisture must not exceed:

  • Cement screed: 2.0%
  • Anhydrite screed: 0.5%
  • Heated anhydrite screed: 0.3%

Consumption

Approx. 1.4 kg/m² per mm layer thickness

Processing

To avoid lump formation during mixing, add approx. 2/3 of the required water first and mix with a suitable basket mixer at approx. 600 rpm. Add the remaining water after the material has opened. Mix for approx. 3 minutes, allow to mature briefly, then remix. Use the prepared material within one hour. Do not rework stiffened material with water. Apply the slurry with a stiff brush, trowel, or suitable spray device in 2–3 coats evenly. Maximum layer thickness: 5 mm. For tile installation in thick-bed method: apply a splatter coat into the second fresh layer. After curing, tiles can be laid in the thick-bed method.

Subsequent Work

Protect fresh waterproofing for at least 3 days from direct sunlight, rapid water loss, extreme heat, drafts, frost, and rain. After approx. 24 h, ceramic coverings can be laid with solvent-free thin-bed adhesives. For outdoor work, coverings must be void-free. Waterproofing must be fully dried before applying protective layers or backfilling (1–3 days depending on temperature and humidity). Ensure no water-retaining soil contacts the waterproofing surface. In such cases, place a 50 cm wide zone of permeable fill material in layers. Coating must be sufficiently cured (7 days) and protected (e.g., gypsum-free plaster, protective boards). Avoid point or line loads. Clean tools and contaminated areas immediately with water. Due to many possible influences, a test application is recommended. Observe the expiration date on the packaging.

Packaging

20 kg bag

Be the first to review this product.

Customers who bought this product also purchased

We Also Recommend